[MostroRodento]

Anyone know if the RoadRacing Oil Temp gauge works for carb'd Monsters?

I believe it is optioned for later models.

Its the one that sits where the handle bar clamps were on the upper triple, once you have gone to clip-ons.
http://www.jacklilley.com/newcart/

 

[lp]

On the kit I received the mounting clamp fits fine but the electrical connectors are all wrong to plug 'n play on my carbed '99. I plan to just chop the loom and wire it up myself.

*EDIT* I found the loom connector I needed for the RR oil gauge kit hidden directly underneath the voltage regulator. Its now installed and fits perfectly. Completely plug n' play with no cutting. The instructions don't show jack sh1t and are written in italian with someones additional pencil scrawlings in french(!) on mine but no excuses, I'm an idiot. :

 

[Norm]

I got one from Stuart for my '96, works great.

 

[Hanjin]

Check out the DML oil temp gauge. It replaces the ugly oil fill plug. I got one and it works great.http://www.ducatimonster.org/tempgauge.html

 

[lp]

If the looms are different between 900/750 bikes that would make sense why mine doesn't plug-in. The main wiring connector is half inch too wide for the matching connector on my 750. Everything else that comes with the kit fits OK.

 

[MonsterHooligan]

Check out the DML oil temp gauge. It replaces the ugly oil fill plug. I got one and it works great.http://www.ducatimonster.org/tempgauge.html

DOH
sold the last one today...if there is enough demand i can get more.

 

[Paul D]

Around here I only worry about the oil being too cold. I didn't block off the cooler this winter like I have before, but I was riding the KLR most of the time.

 

[MostroRodento]

DOH
sold the last one today...if there is enough demand i can get more.

Damn I hope the one you sold was my order!!!!, I Paypal'd yesterday

I decided to go with the DML filler cap version as my dealer couldn't tell me if the RoadRacing set up came in several versions or what...maybe I'll stick a Rizoma clock over the old riser mount mess

 

[TripleDuck]

DOH
sold the last one today...if there is enough demand i can get more.

Jeff:
If you order more, I'll take two.
TripleDuck

 

[test-reg]

order more please!!!

 

[MonsterHooligan]

ok ok I'll get more.

It might take a little while. Pieter sent them from Holland.

It's kinda cool getting stuff in the DML store nobody else sells.

 

[Hanjin]

Here is a bad pic of my new oil temp and pressure gauges.

 

[CETME]

Where did you plug in an Oil pressure Gauge?

 

[Hanjin]

Evoluzione has a tee fitting that plugs into the stock dummy light plug and runs another outlet for the gauge and the dummy light. Part# 50103. Great stuff and cheap $20.00!!

www.evoluzione.net

 

[Hanjin]

Sorry you can't see the temp gauge. But its great looking too.

 

[CETME]

where is this "dummy light" plug?

 

[TurboMonster]

ok ok I'll get more.

It might take a little while. Pieter sent them from Holland.

It's kinda cool getting stuff in the DML store nobody else sells.

Let me know whan you get more or start taking back-orders! My project bike seams to always run hot and it would be nice to be able to monitor it a little better!

 

[Hanjin]

where is this "dummy light" plug?

Right above the oil fill on air cooled monsters, it's screwed into the case.

 

[dutchduc]

Does anybody know how to contac Pieter directly, I couldn't find him in the members list. If he gets the gauge from Holland, I would like to know how to order "direct".

 

[FastKatanBoy]

Order more! For $70, it is a no brainer!
I will take one for sure. I am sure I can get about 2-3 of my 6 Duc riding buddies to buy also.